In this guide from PerLod Hosting, you will learn the differences between iptables vs nftables for high-traffic Linux servers, which focuses on performance and long-term maintainability. You can discover how each firewall framework evaluates packets, how rule structure and rule count can impact throughput and latency, and why rule management becomes a bottleneck on high-traffic systems.
Also, you will learn how rules are written in each system, including common patterns like allowing services, dropping unwanted traffic, and using sets for large allow and deny lists, and then you will learn a safe migration path from iptables to nftables.
The goal is to help choose the right firewall option between iptables vs nftables for production environments. For dedicated servers handling high-traffic workloads, choosing the right firewall framework directly impacts performance and stability.
iptables vs nftables Performance
At this point, you can discover how fast iptables vs nftables can handle network traffic on high-traffic servers. When traffic is high, the firewall should filter packets with the least possible CPU load and the smallest delay.
Core Performance Architecture Differences in iptables vs nftables:
iptables checks rules one by one in order, so when you have lots of rules, it can get slower because each packet may need to be compared against many rules.
nftables can use faster lookup methods like sets, so matching can stay quick even when the list of addresses or ports becomes very large.
Key Performance Metrics from Benchmark Studies:
One academic study tested both firewalls with different packet sizes and different numbers of rules, then measured throughput and latency using iPerf3 and ICMP ping-style checks.
It found that when rules are checked in a simple one-by-one way, nftables could be slower than iptables for very small packets, including 64 to 256 bytes, when the ruleset is very large, including 1000 and higher rules. But when nftables uses faster indexed lookups like set-based matching, the performance was almost the same as iptables, and nftables was sometimes a bit faster with bigger packets and medium-sized rule sets.
Real-World High-Traffic Benchmarks in iptables vs nftables:
The SKUDONET benchmarks showed that nftables handled a lot more load-balancing traffic per CPU core than iptables.
DNAT (destination NAT): iptables around 256k requests/sec per core, nftables around 561k requests/sec per core (about +118%).
SNAT (source NAT): iptables around 262k requests/sec per core, nftables around 609k requests/sec per core (about +132%).
They also found that when you add more backend servers, iptables performance drops faster because it has to check more rules one by one, while nftables scales better because it can match using more efficient structures.
CPU and Memory Efficiency in iptables vs nftables:
Red Hat’s tests showed that iptables usually gets slower as you add more rules, because it has to check more items for each packet. nftables can scale better, because it can organize rules using things like sets instead of long one-by-one lists.
In one test, 100,000 packets per second with a blacklist check, iptables needed a bigger CPU hit than nftables:
iptables: about 40.77% extra CPU cost
nftables: about 17.27% extra CPU cost
Memory can also be very different. With iptables, large IP lists often mean lots of separate entries, so memory usage can grow fast. nftables can store large lists more efficiently using sets, so it typically uses less memory for big allow and deny lists.
Latency and Throughput Characteristics:
On high-traffic servers, it’s not just the average speed that matters; it’s how stable the latency stays when the system is under heavy load.
In Kubernetes tests from 2025, when the setup had 30,000 services, nftables stayed more consistent. Its slowest normal latency (p99) was about as good as iptables' latency (p01). That suggests nftables can deliver more predictable latency when things get extremely large and busy.
Performance Recommendation Between iptables vs nftables: For servers handling over 10,000 concurrent connections or 1 Gbps sustained traffic, nftables provides better performance through:
Hash-based set matching for IP and port blacklists.
Atomic rule updates, which prevent little configuration states.
Early ingress hooks process packets before conntrack overhead.
iptables vs nftables Rules
In this step, you can learn how iptables vs nftables rules are structured. The goal is to make the syntax differences clear and show why nftables often stay cleaner when rule sets grow.
nftables has built-in sets that can handle IP ranges, and you manage them directly in nftables rules without needing extra tools. This makes updates safer because changes apply all at once, and it usually uses less memory when you have very large blacklists.
3. Multi-Action Rules and Logging:
iptables requires separate rules for logging and dropping:
It means the firewall has fewer steps to check for each matching connection, because logging and dropping happen in one rule instead of two, so the rule processing task can be cut roughly in half in that case.
Using the inet family lets you write one rule that works for both IPv4 and IPv6, instead of writing the same rule twice. This makes the firewall config easier to manage and lowers the chance of mistakes like updating IPv4 rules but forgetting IPv6.
nftables can check connection states directly inside the rule itself, instead of relying on extra matching layers. This can reduce extra processing tasks and help the system run a bit more efficiently, especially on high-traffic servers.
How to Migrate from iptables to nftables?
At this point, you learn how to migrate from iptables to nftables in a safe and low-risk way, especially on production servers where a mistake can cause downtime or lock you out.
First, you must check the current backend implementation with the command below:
Bash
sudoupdate-alternatives--displayiptables
In the output, you must see iptables-legacy or iptables-nft backend.
You must back up the existing rulesets by using the following commands:
This ensures legacy scripts continue functioning while using the nftables kernel backend.
Best Recommendation: For high-traffic servers like 1 Gbps or 10,000+ active connections, nftables is often the better choice because it can handle large rule sets more efficiently and is easier to manage as things grow.
Moving from iptables to nftables takes some planning, but it usually pays off long-term because updates apply all at once, one ruleset can cover both IPv4 and IPv6, and large allow and deny lists can be handled efficiently with sets.
Conclusion
iptables is old and reliable, but it can get slow on high-traffic servers because it checks rules one by one. nftables is newer, easier to manage, and can be faster because it handles large rule sets more efficiently. On high-traffic systems like 1 Gbps+ traffic or thousands of connections, nftables can scale better and reduce CPU load, especially when using sets for big allow and deny lists.
We hope you enjoy this guide on iptables vs nftables. Subscribe to our X and Facebook channels to get the latest updates and articles.
No. They conflict because both try to manage the same kernel firewall rules. You must choose one of them. If you use the iptables-nft compatibility layer, it translates iptables commands to nftables, but the backend is still nftables.
Yes. Most major Linux distributions include nftables by default or recommend it. Kubernetes, major cloud providers, and many hosting platforms now prefer nftables for new deployments.
Only if you run them directly as iptables commands. You can either rewrite them for nftables syntax or install the iptables-nft compatibility package to translate legacy iptables commands automatically.
We use cookies to run PerLod and to understand how the site is used. You can accept everything, or open Manage to turn individual categories off. Cookie policy.